Common Types of Finishes

Stain, Paint, and Finish are the three primary classifications for common wood treatments. Stains contain pigments and are used to tint the wood. Paints contain colored pigments and sit on the wood to form a protective coating. Some finishes are simply paint with out the pigment that lay down a clear protective coating. There are five common types of finishes on the market. They are:

• Oil
• Varnish and Polyurethane
• Shellac
• Lacquer
• Water-based Finishes

Applying finishes is one part of woodworking that doesn’t require many tools. In fact there are only three main tools used to apply all of the finishes listed above; rags, brushes, and a spray gun. Many professionals will use a spray gun for thin smooth even coats.

 

Selecting a Clear Finish

When you are selecting a clear finish it is important to remember the qualities you require from the finish.

• It must protect the wood against  vapor exchange.
• It must be durable enough for the intended application.

 

Oil Finishes

These types of finishes have been used for centuries to treat and preserve wood. Oils are different from most other finishes on the market because they seep into the wood and penetrate the wood’s fibers. Because of this, oil finishes cannot be built up to a thick coat like polyurethane or varnish can. They offer less protection but are also easier to apply which is their primary advantage. Another advantage is that simply wiping on more oil can often repair minor scratches.

There are two types of oils, those that cure and those that don’t cure. Oils that don’t cure should generally be avoided because that can continue to seep into the wood leaving the surface unprotected. They can also leave a sticky surface on the wood. Linseed oil and Tung Oil are both oils that cure and work well as finishes.

Applying Oil Finishes

The primary advantage of using these finishes is their ease of application. Simply wipe it onto the surface with a clean cotton rag, wait 10 minutes, and applying more oil and allow time to cure. Always sand the surface lightly between coats. Linseed Oil generally requires three coats to achieve the “hand rubbed” look. Tung Oil may require 5-6 coats to achieve the same results. The first few coats will tend to cure rough but will even out during the last few coats.

Varnish

Varnishes are one of the most protective finishes available. This level of protection increases with additional layers. The primary down side of varnishes is that they are slow drying which can allow dust and dirt time to settle and damage the finish. Because of this it is best if your project is finished in a clean dust-free room if possible.

Varnishes are produced by cooking an oil and mixing it with a resin such as synthetic alkyds, phenolics, and polyurethanes. Interestingly, polyurethane finish is actually varnish made with polyurethane resin to make the finish more protective and durable.

When more oil is used than resin the finish becomes more flexible. This type of varnish is called “Spar Varnish” and is ideal for outdoor use because the flexibility makes it more forgiving of seasonal wood movement.

Applying Varnishes

Achieving a perfect varnish finish is a combination of skill and experiences as well as access to the right tools for the job. Work in a clean dust-free environment. The room should be prepared by wiping it down surfaces with a damp cloth. Also be aware of dust that can be generated by human skin and clothing. The wood should be wiped with a tack cloth and the finish transferred into a separate working container.

Varnish is usually applied with a brush using long steady brush strokes. In contrast to paint varnish brush strokes are much more apparent. Work in the direction of the grain and “tip-off” your brush strokes with lightly brushed vertical strokes. Varnish should be wet sanded between coats with a fine sandpaper.

Wiping Varnish

“Wiping Varnish” that has been thinned with Paint Thinner is also available. Use caution since some manufacturers refer to their wiping varnish as “Tung Oil”. Read the labels carefully since these products are completely different. One way to test this product is to pour some of the finish onto a piece of glass and allow it to dry. If the finish cures to a hard finish it’s varnish. This product can be applied with a brush like varnish or with a cotton rag like an oil finish. The advantage of wiping varnish over an oil finish is that you can leave some of the finish on the surface and build up to a thicker coat.

Oil/Varnish Blends

Just to make thing a little more confusing the finish manufacturers introduced a blend of varnish and tung or linseed oil. These finishes are applied and act similar to an oil finish but the varnish adds some additional protection. They will still cure in the wood like an oil finish and should not be used if you plan on building up layers on the surface.

Shellac

Shellac is one of the few natural resins still in use today. Although not as durable as a Lacquer or Varnish, shellac still provides a modest amount of protection. Shellac is not the best finish for tabletops, chairs, and kitchen cabinets due to high wear requirements of these items.

The big advantage, and the reason the finish is still in use today, is that Shellac is alcohol based which makes it very fast drying. Because Shellac is fast drying it is less likely to collect dust like varnish. It is often too thick to apply with a brush and requires thinning with denatured alcohol before it can be brushed. This finish also requires that you work fast with your brush and maintain a wet edge.

It is available in a range of colors from clear to an orange/amber color. Orange/Amber shellac is known for the warm tones it gives wood. Shellac breaks down over time, so be sure to purchase a fresh can, and don’t use anything over a year old.

Lacquer

Lacquer is used most often in furniture factories because its fast drying properties reduce dust related finish problems. It is usually applied with a spray gun although “brushing lacquers” that cure slowly are also available. If you choose to spray a lacquer finish be aware that the fumes are hazardous to your health and the dry dust can be explosive.

Water-Based Finishes

Because of increasing environmental concerns a new class of finished has been developed. These “Water-Based” finishes are often marketed as “polyurethane”, “varnish”, or “lacquer” which is untrue since all of these finishes are solvent-based. You can tell if a finish is water based because the can should mention “water cleanup” as an added feature. “Water-based” finishes are basically latex paint without a pigment. The two primary downsides are that they tend to hold visible brush marks and are less durable than the more conventional finished. They also tend to bubble with brushing. You’ll want to use a synthetic bristle brush and try not to over-brush the surface. Also try to avoid temperature and moisture ranges that exceed indoor conditions. Moisture or temperature ranges on either end of the scale can cause drying problems.

Sanding your Finishes

Properly preparing your finish between coats is an important step. With finishes that require building to achieve a thick coat it is extremely important to sand with fine sandpaper between coats to remove bumps and high spots. Wet sanding with special “wet sanding” paper is an excellent way to smooth out the surface without creating lots of airborne dust, which could land, in your next coat of finish. The best advice we can offer is to test your finishing techniques on a piece of scrap wood before you move on to your recently completed masterpiece.